I installed a new bathroom faucet and it came with a new drain pipe and sink drain outlet flange. Bonded Windows For Vauxhall Vivaro Seat. The faucet works great but the drain pipe is leaking under the sink. Learn how to find leaks in your irrigation system and fix your broken sprinkler pipe.

How to Cap Off a Sprinkler Head. If you have a sprinkler head you would like removed, you can simply cap it off. Capping a sprinkler head is easy using the following steps. Tip: Paying attention to the efficiency of your sprinkler system can pay dividends. One broken sprinkler head can waste hundreds of gallons of water in a single cycle.

1. Sprinkler problems happen, but usually you can fix them yourself. Today's in-ground sprinklers are designed to be easy to repair and adjust. To keep your sprinkler.
2. Why Do PVC & CPVC Pipes Occasionally Fail? Duane Priddy, Plastic Failure Labs, Midland, MI Preface PVC and CPVC pipes and fittings are.
3. Broken sprinkler heads are easy to identify. Simply look for cracked or broken plastic casing on the heads, heads that don't pop up, or water that sprays wildly or.
4. DIY Network has instructions on how to repair clogged traps, blocked bathroom drains, stopped-up toilets and weak showers.

Check regularly to see that your sprinkler system is working properly and you'll save water and cash. Step 1 - Locate the Dead End The dead end is the last sprinkler in a series. Capping the dead end itself leaves water in the underground line with nowhere to go, and if the sprinklers are spaced far apart, this wastes water pressure. In areas prone to freezing, it can cause water in the line to ice and damage the pipe as well. So, instead, dead ends should be capped at the preceding or next- to- last sprinkler head.

Water Hammer and Air in Pipes Water Pipe Noise and Things that go Bump in the Night. Is your sprinkler system making odd noises? That sound may be water hammer, but.

Step 2 - Remove the Sprinkler Head Use the shovel to dig out an area around the sprinkler head. Dig deep enough so you can access the riser or pipe leading up to the sprinkler head. After you have removed enough dirt, remove the sprinkler head by turning it to the left, or counterclockwise; although, you may need to use one hand to hold the riser in place so it doesn’t twist out as well. If this is a dead end sprinkler head, you can either dig up the entire line for use elsewhere or simply remove the last sprinkler head. You will need to dig around the preceding sprinkler head so the line can be capped, so dig just past the head all the way down to the supply line. Use caution to avoid cracking the line with the shovel.

Step 3 - Install the Cap. With the sprinkler head removed, you should see just the riser coming up from the irrigation line. Use a damp towel to clean the threads of the riser. Now, add Teflon tape to the threads, wrapping the tape two or three times. This will help ensure water does not leak out. Your cap should be the same width as the riser.

Twist the cap onto the end, and add enough force so that it is as tight as possible. For a dead end cap, use PVC cutters to cut the pipe just past the sprinkler head fitting.

Leave enough space for the cap to go onto the pipe, and clean the pipe with PVC primer. After allowing it to dry, apply PVC cement to the outside of the pipe and the inside of the cap, then quickly twist the cap onto the end of the pipe. Step 4 - Test the Seal. To make sure the cap is sealing water in, turn on the sprinkler, and check for any leaks. Step 5 - Fill in the Hole.

With all connections sealed, you can now fill in the hole around the cap. The sprinkler head can be used as a spare or for repair parts.

Since water resources are becoming more precious, especially in drier areas, this is important information to know.

Fixing Sprinkler Systems. Overview: Simple system, easy fixes. An automatic lawn irrigation system is the best way to keep your lawn looking fresh and green. Correctly designed and programmed, it'll deliver the right amount of water to your yard— no more moving the sprinkler! But like any other system, it occasionally breaks down or requires maintenance. The good news is you can handle 9. We'll show you how to identify and fix the most common problems.

Calling in a professional could cost at least $1. Don't be intimidated by the prospect of working on a system that involves both plumbing and electricity. The pipes are plastic and much simpler to repair than the plumbing in your house. The electrical lines are low voltage, so they're not hazardous. You don't need special skills to make the repairs, but you'll need a multimeter to diagnose electrical problems. Figure A: How a Sprinkler System Works. The controller sends a signal to the control valves in the control valve box.

The valves open, sending water through the underground water line, which causes the sprinkler heads to pop up and spray. Figure A: How a sprinkler system works. Sprinkler heads not working? Solution 1: Replace the heads. Replace a sprinkler head.

Dig around the sprinkler head to expose the riser. Unscrew the broken sprinkler head from the riser.

Install the new head, turning it tight with your hands. Simply look for cracked or broken plastic casing on the heads, heads that don't pop up, or water that sprays wildly or not at all. It's common to find the top of the head completely broken off. This typically happens to heads that are set too high and are run over by vehicles or hit by lawn mowers.

Replacing the head is one of the simplest fixes. Replacement heads are available at home centers and online. Be sure to buy the same type of head that you're replacing. To change a broken head, turn off the system and dig a 2- ft.- diameter hole around the head.

Using a square shovel, slice the sod into easy- to- remove pieces. Set the sod on a tarp so you can set it back into place at the end of the job. Dig down to the “riser” (the vertical pipe that branches off the main line) which is connected to the sprinkler head. Dig with a light touch to avoid damaging the plastic water line, which is 8 to 1.

While the head is off, take care not to spill dirt into the riser. Sprinkler heads are installed only hand- tight, but after being in the ground for several years, they may require the use of wrenches to unscrew. If the head doesn't turn easily, hold the riser with slip joint pliers to keep it from twisting loose from the fittings below.

Attach the new sprinkler head by placing it on the riser and turning it hand- tight (photo). Don't use Teflon tape or joint compound on the riser threads. Sprinkler heads are factory tested to make sure they work. As a result, they're often packaged still wet, so don't be surprised to see water in a new head. Before filling in the hole and replacing the sod, set the desired sprinkler pattern (see “Reset the Spray Pattern,” below).

Caution: Before you start digging to access the underground water lines, electrical wires or spray heads, dial 8. Sprinkler heads not working? Solution 2: Clean and reset heads. Photo 1: Unscrew the top. Disassemble the sprinkler head by unscrewing the top from the canister. Rinse away soil and debris in a bucket of water.

Place the head in the canister so the nozzle is at the edge of the area to be watered. Make final adjustments with the water running. Clogged heads may rise but fail to spray, not lower after watering, or produce an erratic spray pattern. To clean the head, dig it out and remove it from the Riser (Photo above).

Take the head apart by holding the bottom of the canister and turning the top of the head counterclockwise. Once it's unscrewed, lift it out of the canister (Photo 1). Remove the plastic screen basket, which serves as a filter, at the base of the head. If you can't pop the basket out with your fingers, pry it out with a flat- head screwdriver or pull it free with a pliers. Rinse the basket in a bucket of clean water, washing out the debris (Photo 2). Clean the rest of the sprinkler head by rinsing it with water. Replace the head on the riser.

If it still doesn't work, replace it with a new head. Note: In areas of the country that experience freezing temperatures, polyethylene (poly) pipe is used for the irrigation water lines. PVC pipe is used in areas that don't freeze. Reset the spray pattern. When putting on a new sprinkler head or using the same head after cleaning, you may need to adjust it to water a specific area. Adjustment methods vary.

You can adjust some head types by turning a slot at the top with a screwdriver. Others require a special key that you insert into the head and turn (Photo 3). Some heads also allow you to adjust the spray pattern by turning a tiny screw located next to the nozzle. Adjust the heads before installing them, then fine- tune them once they're in place with the sprinkler running. First, turn the top clockwise until it stops. That nozzle location is the starting point (the head will turn counterclockwise from there).

Adjust the head to set the watering rotation anywhere from 4. Set the head in the canister. Standing behind the head, align the nozzle with the right edge of the area you want to water, such as along a driveway. Tighten the head in the canister. Carefully backfill the hole and replace the sod. Turn on the sprinklers at the controller. Allow the head to make a few rotations, then make additional adjustments while the system is running.

Low water pressure? Solution 1: Turn on valves at backflow device. Check the valves. Check the valves on the backflow device to make sure they're open. Turn the valve on the horizontal pipe first, then the vertical pipe valve.

In extreme cases, many of the heads won't even pop up. Start with the easiest solution.

Make sure the valves at the backflow device are fully open. The backflow device is located above ground, with the valve at least 1. Most backflow devices have a valve on the horizontal and vertical pipes. Turn the valves to their open positions as shown. The valve is open when the handle is parallel with the pipe. Low water pressure?

Solution 2: Find and repair leaks. Photo 1: Install a slip coupling. Cut out the damaged section of line and replace it with a slip coupling. Secure the coupling with band clamps. Look for a series of sprinkler heads that aren't watering properly. The water line problem is always located between the last working head and the first nonworking head. Look for signs of leaking water, such as water bubbling up from the soil when the sprinklers are running, a depression in the ground, or a very wet area.

If you find running water, follow the water to the highest point to find the source. Once you locate the approximate leak site, dig straight down to the water line. Then enlarge the hole along the line, following the flow of the leaking water until you find the break or crack. Before making the repair, make sure the system is turned off at the controller.

Use a slip coupling to repair the leak. This special coupling contracts to make insertion easy. Find these couplings and other repair parts at irrigation supply stores. To fix the leak, use a hacksaw to cut out a 4- in.

Place a clamp on one of the line ends, insert the coupling, then tighten the clamp. Place a clamp on the second pipe end, expand the coupling while inserting the nipple into the pipe, then tighten the clamp. Backfill the hole with dirt and replace the sod. Low water pressure?

Solution 3: Repair crushed pipes. Photo 1: Crushed pipe. Tree roots can grow around a pipe and squeeze it closed after several years. Photo 2: Splice in new pipe. Cut out the damaged section of line. Desinstaller Mcafee Security Center Vista more.

Replace it with a new section of line, making connections with standard couplings and band clamps. Sometimes, roots wrap around the line and squeeze it closed over the course of several years (photo 1). Or vehicles may have compressed the soil and collapsed the line.